How To Change Oil In Mercury 15 Hp 4 Stroke Outboard

April 03, 2021 Posting Komentar

Install New Oil Filter and Add Fresh Oil. Run the outboard on idle for a minute to distribute the oil throughout the motor.

Mercury Marine 15 20 Hp 4 Stroke Oil Change Kit

EFI 1731cc 1B366823 - 2B094995.

How to change oil in mercury 15 hp 4 stroke outboard. Be sure to follow. High-horsepower outboard including direct fuel-injected engines in extreme marine operating conditions-Far exceeds Quicksilver in-house test standards which are more stringent than the industrys TC-W3 standard. After you change the oil its always a good idea to start the engine again to circulate fresh oil through the engine and to check for leaks.

8 HP - 2001-2004. 10 liter 1000 ml 105 QT. Spraying fogging oil directly into the cylinders via the spark plug hole is a good idea for either type of motor.

If you removed the drain screw to empty your oil carefully reinstall the drain plug. Tilt the outboard up to the trailer position. Do Not use a crankcase oil pump when changing oil or damage may occur.

Fogging oil sprayed into the air intake just flows into the upper cylinder via the intake valve. One major factor in the wear of hydraulic systems like your tilt system is operating without the correct amount of oil or the wrong kind of oil. Mercury 15 to 20HP Tiller Driven - 2006 and Newer 4-Stroke Upgrade Kit This upgrade kit boosts all Tiller Driven 15hp Mercury outboards made since 2006 to 20hp.

Try to use the same brand of oil as the outboard eg. Changing the engine oil and oil filter ensures that any accumulated contaminants and acids in the old oil cannot harm the engine while in storage. The dealer will also stock the Mercury Oil Change Kit for many Mercury outboards.

The amount of oil included in this kit is adequate for most of the specifically noted Mercury outboard models. 045 liter 450 ml 048 QT. The new oil filter should be removed from its package and the o-ring lubricated with a thin coat of fresh engine oil.

15-20 EFI FourStroke Engine Maintenance - Changing Gear Lube. Never put the outboard in long-term storage without changing the oil. Dispose of the used oil according to local law or regulations.

Maintaining your Mercury outboards hydraulic tilt system will ensure that your system works as well and as long as your engine and perhaps longer. 99 HP - 1999-2004. Once oil is completely drained lubricate the seal on the drain plug with oil and reinstall.

Wipe any oil from the outboards lower unit with clean shop rags. Each kit includes oil an oil filter and a drain plug seal in a convenient box. Im looking for a manual for a 4 HP 2-stroke Mercury outboard from 1981.

Lock the outboard in the full tilt-up position. Remove the filler cap from the back of the powerhead then fill the outboard with 3 quarts of Mercury 4-stroke marine engine oil and replace the filler cap. Mercury Oil Change Instructions for 4-Stroke 7590115 HP EFI.

080 liter 800 ml 085 QT. You can simply just type in your zip code and it will give you the nearest Mercury Marine dealer that can do it for you. 15 HP - 1998-current.

Turn the steering on the outboard so that the drain hole is facing downward. Change the Oil. Wash the whole outboard with a mild grease-dissolving detergent and warm water to complete the gear oil change.

2012 15 hp Mercury Outboard 4-stroke I always change the filter when I change the oil. I do use synthetic oil in my older 4-stroke but not until after the warranty period is over. 456 FourStroke 1999 - 2016.

Its Belgian made two cylinder serial 9321742 although Mercury advised that Id need to. Remove the drain plug and drain the engine oil into an appropriate container. A helpful video for maintaining your 15-20 EFI FourStroke Engine.

Find out more about Mercurys distribution partners sponsorship applications and our global locations. EFI 1596cc 1B366822 below. Once you have inspected your spent oil and filter set them aside for proper disposal.

Tilt the engine up to the trailering position. Installation is easy you simply swap out the carburetor with our 20hp carburetor and the propeller with our higher pitched propeller that takes full advantage of the extra horsepower. Turn the outboard so the drain hole is facing downward.

Remove drain plug with a 58 or 16mm wrenchand drain engine oil into an appropriate container. Follow the oil-change instructions in your owners manual and always dispose of waste oil properly. I always use the recommended oil.

For many boat owners this annual oil change is part of preparing the outboard off-season storage. Premium Plus 2-Cycle Outboard Oil Speciﬁcally formulated with a higher concentration marine additive package to meet the needs of. 10 liter 1000 ml 105 QT.

Every 50 hrs I think chep insurance. If you scan this with your smart phone it will give you step by step instructions how to change that oil and if you choose not to change that oil yourself. 10 liter 1000 ml 105 QT.

Mercury Oil Change Instructions for 4-Stroke 1520 Carb. Yamalube oil for Yamaha motors as the engine company has a vested interest in making sure the engine performs well especially. Position outboard so the drain hole is facing downward.

It will coat the cylinder walls with oil. The maintenance schedule for the Mercury 150 FourStroke and for most four-stroke outboards calls for changing the oil and the oil filter every 100 hours or annually. Remove the drain plug with an 18mm wrench and drain the engine oil into an appropriate container.

If your particular outboard requires additional oil please be sure to purchase this separately. EFI 1596cc 1B366822 below.

How To Change Oil In Mercury 9 9 4 Stroke Youtube

Oem Mercury Marine 4 Stroke 25 30hp Efi Outboard Oil Change Kit 8m0081915 Learn More By Visiting The Image Link Th Oil Change Changing Kit Mercury Marine