How To Flush A Mercury 115 4 Stroke

Desember 20, 2021 Posting Komentar

The dust cover snaps off but is attached to the hose by a plastic tab so that it wont get lost. Mercury Racing is known worldwide for its leadership in powerboat racing and production of high performance consumer and race marine products.

Outboard Care Mercury Marine

It has a flushing port on the rear of the lower cowl.

How to flush a mercury 115 4 stroke. Hi I accidentally ran my new Mercury 115 four stroke pro xs with the flush muffs on in the sea. FITTING 1 required per assembly. Flushing with freshwater is a simple task and this Mercury Quick Tip video will show you how.

Thank you for your email regarding our Mercury 115 horsepower Fourstroke engine serial number. Secure shift cable to the anchor pin with hair pin retainer. Thanks for watching this video.

Run the engine for ten minutes to allow treated fuel to reach the carburetor. If you are winterizing your engine add fuel stabilizer. Posted 10-14-2005 0205 AM ET US On the 2006 90hp Mercury 4SEFI manual it clearly states to flush the cooling system by attaching a hose to the rear fitting and run the engine at idle in neutral for at least 5 minutes and even has a picture of the hose going straight into the engine.

All you have to do is lower your engine to the vertical position hook up a hose to the conveniently located flush connector and let the water run for 10 minutes you dont even have to start your engine. Using the Flush Port is about 98 efficient but doesnt flush through the thermostats. Find out more about Mercurys distribution partners sponsorship applications and our global locations.

Take the dust cover off of the flush connector thats on the end of the flushing hose on the front of the engine. Position remote control into neutral. April 2018 12.

I got a new set this one with rectangular suction cups instead of round and this model doesnt seem to work as well or at least the motor when started wont suck up water. FLUSH KIT Coastal 1 required per assembly Fits 75-115 Hp EFI FourStroke outboard engines. For supercharged four-stroke Verado outboards Mercury recommends using the fitting on the port side just below the cowling and turning the hose on about half strength.

Ran it at 4500 rpm for 10 min to a fishing spot then 2 hours later running at 3000rpm for 10 min alarm goes off and I see temperature warning says 70deg. Can starting the engine while flushing using the direct connect hose damage the engine. Now theres a real life experience.

I have an 01 Yammie 115 4 stroke. A water separator may be installed with this engine and you will not need to remove the fuel filter. The flushing port has garden hose threads on it but no cap or plug.

Sometimes on muffs the tstats take a while to openJust make sure motor temp is. Can anyone give me a definitive answer to these questions. N a b c d e f a-Center Mark.

Mercury doesnt give preference to running the engine or not while flushing three minutes is the minimum either way but it shouldnt exceed minimum idle speed if its running. DO NOT run the engine while using this attachment to flush. Align the shift cable end guide with the center point made in Step 2.

For years Ive always used the muffs on the lower unit intake for fresh water flushing but my muffs finally rotted out. I recently bought a boat with a 2011 Mercury 17L 115 hp 4S motor. Mercury 115HP - water not comming through tell tale when flushing with bunny ears Sounds like impeller replacement timeSalt water usage change every 2 years.

Here is the text to add to the video as I do not have the log-inThis how-to-video will show the process of flushing your Mercury outboard. Quickshot keeps the fuel system clean and fights ethanol. The flushing garden hose type attachment on your port side of the engine is for flushing the motor.

Its used to BACKFLUSH all the water SUPPLY passages water tube water pump and the coolant DUMP circuits in the adapter plate. We appreciate this opportunity to respond to your questions. Place shift cable on anchor pin.

Whats the flush port you talked about I know on a 90 horse 4 stroke mercury theres a place up on the back of the motor where you can hook a hose up to and run the motor at idle. 75 90 and 115 4-STROKE INSTALLATION MANUAL Page 11 of 18 4. Heres the good news.

Adjust cable barrel so it slips freely into the barrel holder. 858566A03 - Flush Kit -coastal More info 21833. Is this port to be used only for flushing the silt and salt out without the motor running or can it be used for general.

A helpful video for maintaining your 75-115 FourStroke Engine. Then come back and try hose hook up for flush. Fuel Stabilizer keeps fuel fresh for extended periods.

Allow some time for the fuel conditioner to mix with the tank then run the engine to make sure treated fuel makes it all the way to the engine. Sep 28 2008. Coastal flush port pushes water in two directions-.

If you can please like and subscribe for more videos. I took it out in salt water yesterday and was wondering if I should flush the motor through with fresh water after every tr. Hi I have just purchased a new boat with a 60 HP Mercury 4 stroke outboard.

I turn off motor I realise what has happened and remove flush. Place the outboard in water or connect flushing attachment for circulating cooling water. 1200 hours and no problems.

Interesting to know how many hours the respondents have on their engines I have a 115 4 strokeflushed every time with the garden hose on the engine flush nozzle. Usually ships within 10 days. Serial No1B366823 and above.

Also If you found this Video helpful please leave a comment below. This is the first Mercury that I have owned. Push the hose adapter into the flush connector until you feel the snap of the connection being made.

Mercury 4 stroke flushing. Outboard Spares Response HI to my knowledge you cannot run an engine on the direct flushing attachment. I cant really do any work myself since boat sits on my boat lift and I dont trailer.

Yamaha 1154 stroke flushing motor. When boat service is needed I just ride her to the nearest Mercury repair shop and let them take Tahoe out to do work. Where you hook the hose to is also the p hole and with using this way to deliver water you are running the cooling system in a reverse flow.

If it does nothing I guess I will have to take it back to boat repair shop for a inspection.

How To Change The Oil On A Mercury Outboard Mercury 115 Oil Change Boats Net Youtube