How To Flush A 60 Hp Mercury

November 24, 2020 Posting Komentar

Was going through my motor manual again today when I noticed that the recommended method for flushing the motor is to connect a hose to the tell tale output turn on the water to about 50 pressure and then switch the motor on. Immersing the jet drive in a barrel of water doesnt work either because the water is thrown out.

60r Engine Outboards Mercury Racing

Make sure the motors water pump is working.

How to flush a 60 hp mercury. Hi I have just purchased a new boat with a 60 HP Mercury 4 stroke outboard. Heres the good news. Hondas only recommended flushing procedure for its larger engines 60-250hp - is to use the factory flushing port connected to a garden hose with the engine not running.

Open the engine compartment lid. Run outboard for 2 to 5 minutes to ensure the thermostat opens and fresh water passes through all internal cooling galleries. Flush the outboard with fresh water following use in brackish salt or polluted water to minimize the accumulation of scale and silt deposits in cooling system passages.

I dont own a 60 HP but my 50 HP requires the same flushing procedure. Hondas only recommended flushing procedure is to use the factory flushing port connected to a garden hose with the engine not running. Do not run engine above idle when flushing.

I went and bought a sprinkler 34 in. Saltwater maintenance is made easy in the 40-60hp models with the innovative freshwater flush. You should see a stream of water flowing.

I took it out in salt water yesterday and was wondering if I should flush the motor through with fresh water after every trip out. And cap installed them with a washer which should already be in the motor under the stock plug. However the thermostat even if jammed closed will not be the problem although changing it would be a generally good idea.

Mercury FourStrokes consistently outperform the competition in 0-30 mph acceleration. How important is flushing a 2001 2-stroke Mercury 150 hp motor. Here is the text to add to the video as I do not have the log-inThis how-to-video will show the process of flushing your Mercury outboard.

The flushing process can be completed in just a few minutes doesnt. Shift outboard into nuetral. Start outboard making sure that your outboard is pumping water from tell tail.

Flushing with freshwater is a simple task and this Mercury Quick Tip video will show you how. Water should be flowing out the lower unit on the starboard side when flushing under power through the pee hole. I have just bought a 2004 60 efi my fourth Mercury in 10 years.

Turn off the water and remove hose. Remove this nut with a wrench and remove the spark arrester from the carburetor. They go on to say open tap only halfway to reduce water pressure.

When you use the connector and attached the garden hose via the threaded connector on the back of my Mercury 60hp EFI engine to either flush or warm up the engine with fresh water. Depending on your engine type insert the key or pull the starter to engage the engine. Mercury Smaller and midsize four-stroke outboards use the flush port at the rear of the engine.

The coastal flush port as Mercury calls it is much easier way and does the job better than the ear muffs according to MercuryThis will work on all 150 175 250 Pro XS motors. You cant always flush your motor before leaving the boat landing but you can always flush it in your driveway. The factory owners manual for my Mercury 60 HP 4-stroke says flush w engine running with hose attachment in vertical or tilted position.

Posted 08-16-2006 0558 PM ET US. After completing assembly these instructions should be. Cameron says the reason not to run the engine when using the silent flush port is than there is insufficient water flow around the water pump impellor which could suffer damage as a result.

Make sure the muffs cover the holes turn the water on so that water is coming out of the muffs then start the engine. A call to Mercury confirmed that the titlted position is out of the water. QUICKSILVER 16841Q02 Engine Flushing Kit Engine flushing kit 16841Q02 is for use with 4 hp through 5 hp tw0-cycle Mercury or Mariner outboards Mercury or Mariner 25 hp through 35 hp F25 F35 4-stroke outboards 4 hp through 6 hp 4-stroke outboards serial number OR411837 and lower and 8 hp through 99 hp 4-stroke outboards 2005 and newer.

2005 Mercury 4 Stroke 60 HP engine and its not peeing water Im not an expert. Reinstall the propeller Pg 56. Watch this video by Barry Stokes - host of Fox Sports Outdoors as he provides step-by-step instructions to properly flush your Mercury FourStroke engine.

Remove the hosepipe and the flush fitting replace your plug and youre good to. Locate the spark arrester which is mounted on the carburetor. Start the engine.

For some electric engines youll also need to push and release a button after turning the key. 90-10184020 FEBRUARY 2001 Printed in USA. - 2001 Mercury Marine Page 1 of 26 INSTALLATION MANUAL 25 30 40 50 and 60 HP 4-Stroke NOTICE TO INSTALLER.

Larger engines 60 to 250 hp. Insert the flush fitting its a fitting that allows you to connect a hosepipe to the port in your outboard. All you have to do is lower your engine to the vertical position hook up a hose to the conveniently located flush connector and let the water run for 10 minutes you dont even have to start your engine.

How do you flush a jet that doesnt have a flushing hole. Flushing your outboard engine of saltwater or muddy water is critical to the longevity of your product. Most recently I noticed an issue with the release of the hose from the lower cowling flush bracket so I popped the cowling and noticed my hose was split.

Turn on hose and check your hose is connected to ear muffs correctly and there is good water pressure. Start the engine and flush the cooling system for at least 5 minutes. For more information please consult your Mercury Marine owners manual.

Have a look at the bottom of the leg and you should see a vertical row of holes on either side. Keep engine speed at idle. Check that water is coming out of the telltale whilst the engine is running.

PERFORMANCE Quicker is Better Large-displacement dual overhead cam increases low-end power. Flushing a mercury EFI 60hp 4 stroke. Every time you bring your boat in you should flush your Mercury outboard with fresh clean water to remove aquatic plants mud silt and salt from the cooling system.

Open the water and let it flush for 56 minutes remember to do this while the motor is off. On jet drives in which the cooling pump is attached to the top of the bearing housing it is not possible to provide a flushing inlet. And only Mercury offers a three-year limited corrosion failure warranty.

It is a round air filter that is held to the carburetor by a nut. Backing the boat into some fresh water is the.

Fourstroke 30 60hp Mercury Marine