How Do You Break In A 60 Hp Mercury 4 Stroke

Agustus 11, 2021 Posting Komentar

For boats that plane easily bring the boat up on. CARB Star Rating 3.

Fourstroke 30 60hp Mercury Marine

Boat on plane do not use full throttle then back off of the throttle but keep the boat on plane.

How do you break in a 60 hp mercury 4 stroke. Just follow factory break in procedures and youll be fine check your owners manual for that and use 251 gasoil ratio for first 10 hour break in. 60-250 hp 4-Str 1-15 min 15 min-1 hr 1-2 hrs 2-10 hrs After 10 hrs. Remote fuel tank optional Yes.

Then tighten three-quarter to one turn. Next 8 hours run the motor at all speeds but avoid continuous running at Wide Open Throttle WOT for more than 5 minutes at a time. Proper break-in practices reduce the potential for excessive oil consumption.

Recommended Fuel 87 octaneup to 10 ethanol. Flushing your outboard engine of saltwater or muddy water is critical to the longevity of your product. Is it ok he wonders to fill the crankcase with the new Mercury 25W-40 Synthetic Blend oil assuming that the motor had been shipped from the factory with break in oil.

Plane then reduce the throttle opening to the. Also the more people gear batteries and fuel you have in the boat the lower youll drop in RPMs. Compatible with Smartcraft Digital Technology Yes.

Like everyone else said do what the manual says. 2 For the second hour of operation. It also helps to achieve better engine performance levels for a longer period of time.

Thread water hose into the rear fitting. Not saying you will but you could. 90-10184020 FEBRUARY 2001 Printed in USA.

Run the engine at 2000 rmin or at approximately half throttle. Recommended for more engines on the market than any other 4-stroke oil Top selling 4-stroke marine oil 5 years of Engineering and development Approved by Quicksilver engineers and meets warranty requirements for all marine 4-stroke engines - Yamaha Honda Suzuki Volvo JohnsonEvinrude NissanTohatsu Force Mariner 3. Start the engine and flush the cooling system for at least 5 minutes.

Heat Cycles are what are done on a dyno to any new race engine to break it in. During the break-in period you should use a 251 oilfuel mixture 2 pints of oil for every 6 gallons of gas. If you removed the drain screw to empty your oil carefully reinstall the drain plug.

Partially open the water tap 12 maximum. Clean the mounting base and apply a small layer of clean oil to the filter gasket. Normally your Tohatsu outboard uses a 501 oilfuel mixture 1 pint of oil for every 6 gallons of gas.

Do not open the water tap all the way as this allows a high pressure flow of water. Videos you watch may be added to the TVs watch history and. 1 For the first hour of operation.

A future engine failure caused by improper break-in may not be covered by the Mercury warranty so its well worth the time and effort to get your. The new oil filter should be removed from its package and the o-ring lubricated with a thin coat of fresh engine oil. The main thing you want to do is heat up and cool down the engine in a controlled manor.

Screw the new filter on until the gasket contacts the base. Engine Protection Operator Warning System Low oil pressure Overheat Over-rev. Recommended Oil Mercury 4-Stroke Outboard Oil.

Please note your Mercury outboard owners manual will detail the recommended break-in procedure for your engine model. The short answer is yesgo ahead and use the new Mercury oil. - 2001 Mercury Marine Page 1 of 26 INSTALLATION MANUAL 25 30 40 50 and 60 HP 4-Stroke NOTICE TO INSTALLER.

Once the hour meter hits the 10-hour mark the break-in process is complete and you are free to run the engine as you normally would. The 4 stroke 60 is 248 pounds. From Yamahas F115 Owners Manual.

Watch this video by Barry Stokes - host of Fox Sports Outdoors as he provides step-by-step instructions to properly flush your Mercury FourStroke engine. After completing assembly these instructions should be placed with the product for the owners future use. Say you just put a new engine in aYZ450 dirt bike and you want it.

Thanks Well if you are talking reliability. The good news is its easy and simple to do. Do not use grease.

Its super easy to install and lets you view the most critical engine parameters on your cellphone with an app including the number of engine hours and RPM which helps you to stick to the break-in schedule. Its the exact same engine as the Yamaha F115. For more information please consult your Mercury Marine owners manual.

10 hoursRun the engine under load in gear with a propeller installed as follows. Remove the oil-fill cap and add oil to the proper operating level. You can add 501 gasoil ratio on top tanks 10 hour mix leftovers.

If playback doesnt begin shortly try restarting your device. Once you have inspected your spent oil and filter set them aside for proper disposal. Speed is not my main concernjust want the most reliable motor i can get for my money.

Run the outboard motor up to a maximum of. If you do a lot of cruiseing I would say you could go longer alot of stop and go trolling and snotty weather then you can do it earlier for good measure. I let the oil completely drain from the motor before I removed the filter and had No drips there either.

Basically you are looking at the color of the oil if it is getting dark then stick with the OEM recommended interval. Since you do it yourself heck why not more often. Vary throttle during this time.

Shift outboard into neutral. Short full-throttle bursts are acceptable but do. I have a suggestion though.

The reader has a new Mercury four-stroke outboard thats due for its initial oil change. Get Mercurys VesselView Mobile for your motor. This means you shouldnt go faster than about 34-throttle rather than wide-open throttle during the second hour of your 10-hour break-in process.

Run engine at maximum of 2000-3000 rpm. Shaft Length 15 in 381mm 20 in 508 mm Dry Weight Lightest model available 216lbs 98kg. Shift into gear as.

Keep engine speed at idle. Do not run engine above idle when flushing. Step 3 Restrain yourself during the next eight hours of boating -- you may operate at WOT for only five minutes at a time.

Not operate the motor continuously at full throttle. Please see the TLDI break-in chart listed below. Run the engine at.

I just changed the oil in my Mercury 60 hp 4 stroke and had very little clean up. Next 60 minutes. Youll turn 200 RPMs less in the heat and humidity of Summer than cool Spring.

If the motor revs to 6000 I would prop it closer to 6000 this time of year. After completing the 10 hours of break-in commence normal operation. Do NOT operate the engine below 1500 rpm for extended periods of time.

4000 to 5000 rpm or 50 to 80 of throttle.

2011 Mercury 60 Hp 4 Cyl 4 Stroke 20 Bigfoot Outboard Motor